|
Contact Schenck Process:
|
|
Conveying and Filtration
800-821-2476
Weighing and Feeding
888-742-1249
|
|
Offering a Full Line of Replacement Filters
|
High Quality Sound Enclosures
|
|
|
Introducing the new CMD Airlock
The new CMD Airlock is ideal for applications where dry raw or finished products are being handled in the process and where inspection or system clean-out are required. Because the CMD is designed for high process rates and possesses a number of features suited for sanitary processes, the airlock is perfect for food and pet food applications. The CMD is also a direct replacement for traditional square inlet Schenck Process MD airlocks in plant applications where sanitary requirements have increased, but the existing system does not allow for the use of a round inlet airlock.
Features:
- Easy access to seals with rotor removed from endplate
- All stainless steel construction, with the exception of the endplate bearings
- Close clearance design reduces overall leakage through the valve and minimizes pneumatic system losses
- Maximum 32 Ra finish on all wetted (product contact) parts
Download Product Literature
|
Integral Broken Bag Detector
Schenck Process offers Integral Broken Bag Detectors from Auburn Systems. The TRIBO.dsp U3200 Integral model is an advanced and economical particulate detector for dust collector compliance, maintenance, and process applications. The U3200 is designed to monitor fabric filter baghouses, cartridge filters, cyclones, and all types of dust collection equipment. For dry solids flow applications, the U3200 can detect flow/no flow and even high or low flow conditions in pneumatic conveying, injection, or gravity fed process flow applications.
Applications:
- Emission Monitoring
- Bag Leak Detection
- Dust Collector Maintenance
- Product Loss Prevention
- Equipment Protection
- Cyclone Overflow
- Flow/No Flow Detection
|
Tech Tip: Nozzle Alignment
Tips from Schenck Process Service Technicians to ensure your equipment continues to run accurately and efficiently
|
Improper helix and nozzle alignment can cause an open flight helix to break at the drive hub. When the nozzle is not perpendicular to the frame of the feeder, the helix is forced into continuous flexing at the drive hub causing metal fatigue.
The nozzle needs to be installed perpendicular to the feeder both up/down and side/side. When installing the nozzle on a series feeder, set the nozzle perpendicular to the frame of the feeder and tighten down the band clamp holding the nozzle. If the nozzle has a nozzle support, set the nozzle support to the proper height and tighten down the band clamp.
The MECHATRON® feeder is designed with a nozzle support bracket that bolts directly to the nozzle flange, eliminating any alignment issues. Extended nozzles still require a cable support.
Key points to remember:
- The nozzle should be perpendicular to the frame of the feeder. Check using a level or right angle square.
- Extended nozzles need to be properly supported
If you have any accuracy concerns or any other questions please contact our Technical Service group at 888-742-1249 x3.
|
|
Meet Enid Crawford, Aftermarket Sales Rep
Enid Crawford has been with Schenck Process for the past four years. She serves as Aftermarket Sales Representative for Minnesota, North Dakota, South Dakota and parts of Wisconsin.
Enid has been working in industrial sales for over 20 years and enjoys helping customers. "I provide my customers solutions, whether it is parts, components or technical information for their equipment. If I don't have the answer, I have so many avenues to provide them with the information they need."
Enid grew up in Tulsa, OK and has lived in the Kansas City area since 2008. In her spare time she enjoys traveling with her family in their RV and long distance running. "I have grown to love distance running, along with the physical benefits it's a means of clearing my mind."
|
New Phone Numbers at our Whitewater Office
All Aftermarket Sales Representatives at our Whitewater office (weighing and feeding) have new direct phone numbers.
| Jen Snippen |
Northeastern states, CO, WY, NM and Canada Rep |
262-472-6433 |
| Jaime Ramlow |
Southern, Southeastern states Rep
|
262-472-6436
|
| Erin Winger |
Midwestern states Rep |
262-472-6440
|
| Dora Schuck |
Western states, TX, Mexico and Central America Rep |
262-472-6431
|
| Steve Sweeney |
Aftermarket Application Engineer |
262-472-6439 |
|
|
